Manual:Navigation Computer

From VsWiki
Revision as of 22:22, 16 March 2005 by 202.50.187.13 (talk)
Jump to: navigation, search
arrow_left.png Map Mode arrow_up.png Manual Communication arrow_right.png

It is requested that additional image(s) should be included in this article, if possible. Once suitable additions have been made, you may remove this template message.
See Category:Requested_images for other pages that are in need of images.

Navigation Computer

Add image of initial Navigation Computer





So you want to get to the xxxxx System from yyyyy in the shortest number of jumps. Perhaps you'd like to avoid any Area System, and on the way visit an Oceanic planet. How do you do it?

Introducing the Navigation Computer! With this powerful tool you can calculate your travel in the VegaStrike Universe while avoiding those unsavory systems, or perhaps you're interested in the wild side of life!

The Navigational Computer provides two advanced functions. List Mode will allow you to add, rename and delete paths, toggle path visibility. Edit Mode allows you to edit the specifics of a created path. Note that all newly created paths will have to be edited before they are useable.

The Navigation Computer is accessed throught the in-flight Map Screen. Activate the Map screen by pressing SHIFT_LEFT_EN.png M_EN.png and then select the [Nav Computer] button.

List Mode

List Mode allows you to add, rename and delete paths, as well as toggle the path visibility.

Add image of List Mode



[Add] = Add a new path to be edited.

[Edit] = Access Edit Mode to edit a highlighted path.

[Show] = Display highlighted path in the Sector Map.

[Show All] = Display all listed paths in the Sector Map.

[Show None] = Do not display any paths in the Sector Map.

[Rename] = Rename highlighted path (enter new name).

[Remove] = Remove highlighted path from list.

Up/Down = Scrolls listed paths (ED: currently disabled).

Left Box = List of existing paths.

Right Box = Information pertaining to the current path such as visibility, source & destination systems.

Edit Mode

Add image of Edit Mode



A source node and a destination node define each path the player creates. (Note: another way to think of nodes is points; any trip has a starting point and a finishing point). In most cases, the default source node (your current system) should be sufficient, but more complex searches with varying starting points are possible. Notice the box in the bottom right. That contains the node that you are currently building. When you are finished building the node (below), you can apply it to the path, either as a source node by pressing the [Source] button, or as a destination node by pressing the [Destination] button – with two exceptions discussed below.

The node you are creating appears in the bottom right box. There are three different types of nodes you can build:

Adding a System Node

These nodes correspond directly to specific systems. Press the [Current] button to use the current system (the current system always refers to the system your ship is in). The target system always refers to whatever system you have targeted in the Sector Map. The last option will always refer to the system named on the button. You can change the system named on the button by selecting a different system on the map. On the map, the system you are in has a red box around it, while the targeted system has a yellow box and the selected system a green one.

Adding a Criteria Node

These nodes do not refer to a specific system, but rather they will match up to any system meeting a certain criteria. The different criteria types are [Owned By], [Contains] and [Sector]. To add a criterion to the list, simply select a criteria type and then type in a value in the box. For example, if the node should match systems with a Refinery, select [Contains] and type Refinery in the box. Press [AND] to add it to the list. Remove criteria by highlighting and pressing the [Remove] button.

Two commands add additional criteria: [AND] and [OR]. Select your new criteria type and enter the value. Then select your pre-existing criteria, and press the appropriate function. You may also exclude criteria by selecting a pre-existing criteria and pressing [NOT]. This method allows you to select a destination as follows: CONTAINS (Refinery) AND NOT OWNEDBY (Kilrathi). There's a lot of potential in these types of nodes. Note: Since these nodes do not refer to a specific system, they cannot be applied as source nodes.

Adding a Chain Node

These nodes refer to the solutions of other path searches. This is best explained through example: you have one search path (GreatSearch) - which takes you from system A to system B, but you then want to continue the path to system C. Chaining will create the route from A to B to C. This is done by using the destination of the first search as the starting point of the second search. First create and highlight your original path (GreatSearch), then select whether you want to copy the point from [Source], [Destination] or [All Points]. In this case you would select [Destination]. Then press [Chain] to create the node.

The [All Points] option might seem confusing at first, but imagine you have an existing route named (GoodPath), going from A to B. You also need to stop at an agricultural planet along the way. Create a new path (NewPath) and make the source node a Chain Node by selecting (GoodPath) and [All Points] option, clicking [Chain] to create the chain, and then [Source] to apply it to (NewPath). Then use a regular Criteria Node to supply the destination. Now you have a second path that represents the route to the closest agricultural planet along the way. It is similar to finding the closest hotel from the highway when you are planning a long road trip.

The second exception with applying nodes to paths is that the Navigation Computer checks Chain Nodes to ensure there are no cycles before applying a node. By way of example, you cannot create the following: Path A refers to Path B, which refers to Path C, which refers back to Path A; this would imply a cycle. If a cycle would be created, the navigation computer will simply refuse to apply the node to the path.

Using Your Calculated Paths

Add image of map showing path





So you've created a really great trip path. How do you follow it?


arrow_left.png Map Mode arrow_up.png Manual Communication arrow_right.png